search

Minelab GP 3500 User Manual Page 8

  • Download
  • Add to my manuals
  • Print
  • Page
    / 30
  • Table of contents
  • BOOKMARKS
    • Rated. / 5. Based on customer reviews
Page view 7
complete assembly instructions
– continued
page 8
l 2 assembly l
GP 3500
page 8
Adjust for your own comfort
Step 1. Adjust the bungy cord (21) from the knuckle (22) on the shaft
to the correct length to take some of the weight when prospecting.
Step 2. Adjust the hand strap on the handle (9) for your own comfort.
Step 3. Adjust the rear harness strap on the battery bag so that the battery
sits at a comfortable position on your back. The ideal position is when
the weight of the battery counter balances the weight of the detector, and
you can still switch on the detector without putting excess strain on the
bungy cord. Taking the time to adjust your detector properly is very
important for comfortable long term detecting.
TIP: You may need to change the length of the bungy cord or the position of the
bow knuckle when you change coils or detect on sloping ground.
batteries
l 3 batteries l
page 9
GP 3500 GP 3500
www.minelab.com
page 9
The Battery
The 6V rechargeable battery can provide enough power to operate the detector for
14-15 hrs, when fully charged.
The battery may be recharged at any time during the discharge cycle.
It is very important to fully charge the battery before storage.
Do not leave a battery fully discharged for longer than one day.
CAUTION: Never use a 12V battery because this could damage the detector. This damage
is not covered by warranty. The GP 3500 power supply is internally regulated and using an
external regulated power supply is not necessary, and may damage your detector. If you wish
to operate your detector at full power for longer, we would recommend that you own two
batteries and swap halfway through the day.
Low battery indication
If the battery level drops below the required power to give adequate function, a series of alarm
signal pulses are given at half second intervals.
Charging the battery
Step 1 Turn the detector Off before disconnecting the battery.
Step 2 Disconnect the battery cable from the detector and connect to the appropriate
charger.
Battery chargers
Two types of battery chargers (Mains and 12V Vehicle Charger) are supplied.
Important
When charging, the battery must be kept in an upright position.
Page view 7
1 2 3 4 5 6 7 8 9 10 11 12 13 ... 29 30

Comments to this Manuals

No comments
Related products and manuals for Measuring, testing & control Minelab GP 3500
Measuring, testing & control Minelab F3 Specifications   (44 pages)
Measuring, testing & control Minelab Musketeer ADVANTAGE Instruction Manual   (19 pages)
Measuring, testing & control Minelab Relic Hawk User Manual   (11 pages)
Measuring, testing & control Minelab Quattro MP User Manual   (14 pages)
Measuring, testing & control Minelab X-Terra 505 Instruction Manual   (96 pages)
Measuring, testing & control Minelab EXPLORER II Service Manual   (35 pages)
Measuring, testing & control Minelab X-Terra 70 User Manual   (3 pages)
  • Multimac WRAP Sea Hunt WI-BRIDGE Nexotek
  • Robic Unknown Q-See Unknown JVC TV set-top boxes Raypak Unknown Memorex Dictaphones
  • Zephyr PRWB24C32AG Samsung SM-G928F Whirlpool HSCX 80530 Hamilton Beach 58158 Konica-minolta bizhub 454e
  • Whirlpool AWG 870 Instruction for Use Medialink MWN-USB54G User's Guide AEG L6FB84GS User Manual Lenovo IdeaPad Y580 User Manual