Minelab EXPLORER II Service Manual Page 51
- Page / 112
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
THE MINELAB EXPLORER II
45
QUICKSTART
5
Digital display
Figure 5.7, 5.8
When the Smartfind screen is displayed, pressing the DETECT
shortcut button on the control panel switches to the Explorer II’s
alternative Digital display.
The display rates both the ferrous content and the conductivity of
an object with numbers from 0-31. The number for ferrous
content is under the label ‘Fer’ and that for the conductivity is
under the label ‘Cond’. A value of 0 represents low ferrous
content and 31 represents high ferrous content. Similarly, 0
represents low conductivity and 31 represents high conductivity.
The right of the digital read-out you will see an icon representing
the possible target and, in full screen display, a list of displaying
up to three possible target classifications.
It is important to note that the discrimination settings (either the
current Discrimination Pattern or the Iron Mask are still active and
targets outside the accepted area will not update the display. If
you want to adjust the discrimination, simply press the DETECT
button to return to the Smartfind display.
HINT The digits shown in Digital display are a numeric
estimation of the horizontal and vertical position of the
target crosshair displayed in Smartfind mode (that is, its
ferrous and conductivity rating).
As you familiarize yourself with each display, try switching
from one to the other to compare the results.
QUICKSTART’S DIGITAL DISPLAY
QUICKSTART’S DIGITAL DISPLAY
Preferred Display
The Explorer II remembers which
display was last used in your
detecting. If this happens to be
Digital, this display will appear
next time you turn on the detector.
It should be noted that any
adjustments to discrimination that
are made in Smartfind will be
retained and used in Digital.
Figure 5.7 Quickstart’s Digital Display
Figure 5.8 Digital as full screen display
P0611-A
P0612-A
- Minelab Explorer II 1
- TABLE OF CONTENTS 3
- Introduction 7
- ABOUT THIS MANUAL 8
- Contact Minelab 9
- MINELAB’S UNIQUE TECHNOLOGY 10
- Getting Lost? 11
- Discrimination 12
- Operating Frequencies 13
- THE MINELAB EXPLORER II 14
- Assembly 15
- ASSEMBLING THE DETECTOR 16
- CONNECTING THE SEARCH COIL 17
- THE SHAFT ASSEMBLY 19
- CONNECTING THE SHAFT ASSEMBLY 20
- Coil not connected? 21
- THE HANDLE ASSEMBLY 22
- Headphone 24
- Pull Coil Cable 26
- Batteries 27
- THE BATTERY PACK 28
- Safety Tip 29
- Recharging 29
- BATTERY PERFORMANCE 31
- Battery Life 31
- More detecting time? 31
- Battery Performance 31
- Control Panel 33
- THE CONTROL PANEL 34
- BACKLIGHT 35
- MENU AND BACK BUTTONS 36
- SHORTCUT BUTTONS 37
- Iron Mask 38
- Pinpoint 38
- SHIFT BUTTONS 39
- Quickstart 41
- GETTING STARTED 42
- Display memory 42
- INCORRECT 43
- QUICKSTART DISPLAY 44
- QUICKSTART’S SMARTFIND 46
- THE IRON MASK 49
- Iron Mask Shortcut 49
- Operating in Iron Mask 50
- Figure 5.6 50
- QUICKSTART’S DIGITAL DISPLAY 51
- Preferred Display 51
- MODIFYING THE DISPLAY 52
- ADJUSTING SENSITIVITY 53
- Noise Cancel 53
- ADJUSTING THRESHOLD 54
- Display Icon 54
- AUDIO RESPONSE 55
- Headphones Caution! 55
- AUDIO MENU 56
- Headphones 56
- AUDIO: ADJUSTING THE VOLUME 57
- Figure 5.16, 5.17 58
- AUDIO: ADJUSTING THE TONE 59
- AUDIO: ADJUSTING THE SOUNDS 60
- PINPOINTING THE OBJECT 63
- Using Pinpoint 64
- Figure 5.21 64
- RECOVERING THE OBJECT 65
- Fill your holes! 65
- SELECTING TARGETS 66
- ADVANCED MODE OPTION 69
- Advanced Use 71
- ADVANCED MODE’S MAIN MENU 72
- STARTING IN ADVANCED MODE 73
- Are you ready? 73
- ADVANCED MODE’S DISPLAYS 74
- ADVANCED MODE’S LEARN DISPLAY 75
- LEARNING TARGETS 76
- Silence please! 76
- LEARN’S TARGET SELECTION 77
- ADVANCED MODE’S EDIT DISPLAY 79
- EDITING PATTERNS 80
- Continued next page 81
- EDITING AND SAVING TARGETS 82
- ADVANCED MODE’S SELECT MENU 83
- SAVING TARGETS 84
- Saving Shortcut 84
- Volume Shortcut 85
- OPTIONS MENU 86
- OPTIONS: NOISE 87
- Noise Shortcut 87
- OPTIONS: RESPONSE 88
- OPTIONS : RESPONSE 89
- OPTIONS: RECOVERY 90
- SETTINGS MENU 91
- Get into the habit 92
- User Info 93
- HELPFUL HINTS 94
- Leading Alkaline 96
- USER PREFERENCES 97
- QUICKSTART MENU STRUCTURE 100
- ADVANCED MENU STRUCTURE 101
- TROUBLESHOOTING 102
- SERVICE REPAIR FORM 103
- WARRANTY 105
- EXPLOPLORER II 106
- EXPLORER II MODEL 107
- GLOSSARY OF TERMS 108
- DETECTOR CARE AND SAFETY 112
Related products and manuals for Measuring, testing & control Minelab EXPLORER II
(25 pages)
(94 pages)
(11 pages)© 2020, manymanuals.com. All rights reserved. | 0.377 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals