Minelab EXPLORER II Service Manual Page 65
- Page / 112
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
THE MINELAB EXPLORER II
59
QUICKSTART
5
"
RECOVERING THE OBJECT
For this procedure you’ll need: a knife or trowel, a small spade
and a sheet of plastic.
STEP 1 Once the object has been pinpointed, clear the surface of
loose material and check again for the signal. If there is no
signal then the object is amongst the surface material. In
this case, search the surface material until the object is
located.
STEP 2 If the object is still in the ground, check again using
Pinpoint. If you are about to dig in a grassy area, first
remove a plug of grass using a sharp knife or trowel.
STEP 3 Dig carefully to avoid defacing or devaluing the object. The
use of probes can often aid in locating the exact position of
the object prior to digging.
STEP 4 Place the grass plug and all soil you dig onto a plastic sheet
beside the hole. This sheet (which can be folded small
enough to fit into your pocket) enables you to keep all soil
for refilling the hole and prevents material being scattered
about the area.
STEP 5 Check the hole for the object. If it is not in the hole, place
the detector on the ground and with the coil flat, pick up dirt
by the handful and pass over the coil. Be sure you are not
wearing any metal objects like rings, bracelets or a watch
which may interfere with the signal. If you receive no
response, return the dirt to the hole. Repeat this procedure
until the object is located.
STEP 6 Check the hole again with the detector. Ensure that no other
objects remain, then refill the hole. All soil on the plastic
sheet should be returned to the hole followed by the plug of
grass. This should leave the area as you found it.
Fill your holes!
For the safety of others and in the
interests of respecting the
environment, ensure you leave an
area of ground as you found it.
Leaving holes, or an area ‘scarred’
may result in action being taken to
prevent the use of metal detectors
(which spoils the hobby for others
as well as yourself!)
#
RECOVERING THE OBJECT
- Minelab Explorer II 1
- TABLE OF CONTENTS 3
- Introduction 7
- ABOUT THIS MANUAL 8
- Contact Minelab 9
- MINELAB’S UNIQUE TECHNOLOGY 10
- Getting Lost? 11
- Discrimination 12
- Operating Frequencies 13
- THE MINELAB EXPLORER II 14
- Assembly 15
- ASSEMBLING THE DETECTOR 16
- CONNECTING THE SEARCH COIL 17
- THE SHAFT ASSEMBLY 19
- CONNECTING THE SHAFT ASSEMBLY 20
- Coil not connected? 21
- THE HANDLE ASSEMBLY 22
- Headphone 24
- Pull Coil Cable 26
- Batteries 27
- THE BATTERY PACK 28
- Safety Tip 29
- Recharging 29
- BATTERY PERFORMANCE 31
- Battery Life 31
- More detecting time? 31
- Battery Performance 31
- Control Panel 33
- THE CONTROL PANEL 34
- BACKLIGHT 35
- MENU AND BACK BUTTONS 36
- SHORTCUT BUTTONS 37
- Iron Mask 38
- Pinpoint 38
- SHIFT BUTTONS 39
- Quickstart 41
- GETTING STARTED 42
- Display memory 42
- INCORRECT 43
- QUICKSTART DISPLAY 44
- QUICKSTART’S SMARTFIND 46
- THE IRON MASK 49
- Iron Mask Shortcut 49
- Operating in Iron Mask 50
- Figure 5.6 50
- QUICKSTART’S DIGITAL DISPLAY 51
- Preferred Display 51
- MODIFYING THE DISPLAY 52
- ADJUSTING SENSITIVITY 53
- Noise Cancel 53
- ADJUSTING THRESHOLD 54
- Display Icon 54
- AUDIO RESPONSE 55
- Headphones Caution! 55
- AUDIO MENU 56
- Headphones 56
- AUDIO: ADJUSTING THE VOLUME 57
- Figure 5.16, 5.17 58
- AUDIO: ADJUSTING THE TONE 59
- AUDIO: ADJUSTING THE SOUNDS 60
- PINPOINTING THE OBJECT 63
- Using Pinpoint 64
- Figure 5.21 64
- RECOVERING THE OBJECT 65
- Fill your holes! 65
- SELECTING TARGETS 66
- ADVANCED MODE OPTION 69
- Advanced Use 71
- ADVANCED MODE’S MAIN MENU 72
- STARTING IN ADVANCED MODE 73
- Are you ready? 73
- ADVANCED MODE’S DISPLAYS 74
- ADVANCED MODE’S LEARN DISPLAY 75
- LEARNING TARGETS 76
- Silence please! 76
- LEARN’S TARGET SELECTION 77
- ADVANCED MODE’S EDIT DISPLAY 79
- EDITING PATTERNS 80
- Continued next page 81
- EDITING AND SAVING TARGETS 82
- ADVANCED MODE’S SELECT MENU 83
- SAVING TARGETS 84
- Saving Shortcut 84
- Volume Shortcut 85
- OPTIONS MENU 86
- OPTIONS: NOISE 87
- Noise Shortcut 87
- OPTIONS: RESPONSE 88
- OPTIONS : RESPONSE 89
- OPTIONS: RECOVERY 90
- SETTINGS MENU 91
- Get into the habit 92
- User Info 93
- HELPFUL HINTS 94
- Leading Alkaline 96
- USER PREFERENCES 97
- QUICKSTART MENU STRUCTURE 100
- ADVANCED MENU STRUCTURE 101
- TROUBLESHOOTING 102
- SERVICE REPAIR FORM 103
- WARRANTY 105
- EXPLOPLORER II 106
- EXPLORER II MODEL 107
- GLOSSARY OF TERMS 108
- DETECTOR CARE AND SAFETY 112
Related products and manuals for Measuring, testing & control Minelab EXPLORER II
(25 pages)
(94 pages)
(11 pages)© 2020, manymanuals.com. All rights reserved. | 0.137 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals