Minelab EXPLORER II Service Manual Page 53
- Page / 112
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
THE MINELAB EXPLORER II
47
QUICKSTART
5
ADJUSTING SENSITIVITY
Sensitivity control
The sensitivity bar indicates how responsive the detector is to a
target in the presence of ground noise and/or electromagnetic
interference.
The degree of sensitivity is increased by pressing the top shift
button and decreased by pressing the bottom shift button (on the
left side of the control panel). Pressing the center left shift button
switches between semi-auto and manual sensitivity.
Semi-auto
A line cycling around the number indicates that the detector’s
sensitivity is in semi-automatic mode. In this mode, the detector
continuously monitors the environmental conditions and will
adjust actual detector sensitivity as close as possible to your
specified level of stability, depending on these conditions.
Manual
In the manual mode (where the line does not cycle around the
number) the adjustment controls the sensitivity directly. This
mode is suitable for the beach and very quiet (unmineralized)
ground. Manual sensitivity is also recommended for high trash
areas when best results are obtained by sweeping the coil very
slowly.
A high manual number is preferable for stable conditions with low
interference. A low number is suggested for very variable, ‘noisy’
conditions.
Adjusting sensitivity
The highest sensitivity setting (32) is suitable in only the least
‘noisy’, most stable environments. Decreasing sensitivity will
stabilize the detector where it is affected by noise or interference,
but will marginally affect depth penetration and detection of small
objects. This may still be preferable to operating with excessive
background ‘chatter’.
ADJUSTING SENSITIVITY
So that you can detect in best
conditions, we would advise you to
always choose the channel with
least interference before beginning
your detecting session.
If the detector becomes noisy and
you suspect electromagnetic
interference, change to a better
channel before adjusting
sensitivity.
To do this automatically, press the
Noise Cancel shortcut button, or
manually select the least noisy
channel.
Noise Cancel
- Minelab Explorer II 1
- TABLE OF CONTENTS 3
- Introduction 7
- ABOUT THIS MANUAL 8
- Contact Minelab 9
- MINELAB’S UNIQUE TECHNOLOGY 10
- Getting Lost? 11
- Discrimination 12
- Operating Frequencies 13
- THE MINELAB EXPLORER II 14
- Assembly 15
- ASSEMBLING THE DETECTOR 16
- CONNECTING THE SEARCH COIL 17
- THE SHAFT ASSEMBLY 19
- CONNECTING THE SHAFT ASSEMBLY 20
- Coil not connected? 21
- THE HANDLE ASSEMBLY 22
- Headphone 24
- Pull Coil Cable 26
- Batteries 27
- THE BATTERY PACK 28
- Safety Tip 29
- Recharging 29
- BATTERY PERFORMANCE 31
- Battery Life 31
- More detecting time? 31
- Battery Performance 31
- Control Panel 33
- THE CONTROL PANEL 34
- BACKLIGHT 35
- MENU AND BACK BUTTONS 36
- SHORTCUT BUTTONS 37
- Iron Mask 38
- Pinpoint 38
- SHIFT BUTTONS 39
- Quickstart 41
- GETTING STARTED 42
- Display memory 42
- INCORRECT 43
- QUICKSTART DISPLAY 44
- QUICKSTART’S SMARTFIND 46
- THE IRON MASK 49
- Iron Mask Shortcut 49
- Operating in Iron Mask 50
- Figure 5.6 50
- QUICKSTART’S DIGITAL DISPLAY 51
- Preferred Display 51
- MODIFYING THE DISPLAY 52
- ADJUSTING SENSITIVITY 53
- Noise Cancel 53
- ADJUSTING THRESHOLD 54
- Display Icon 54
- AUDIO RESPONSE 55
- Headphones Caution! 55
- AUDIO MENU 56
- Headphones 56
- AUDIO: ADJUSTING THE VOLUME 57
- Figure 5.16, 5.17 58
- AUDIO: ADJUSTING THE TONE 59
- AUDIO: ADJUSTING THE SOUNDS 60
- PINPOINTING THE OBJECT 63
- Using Pinpoint 64
- Figure 5.21 64
- RECOVERING THE OBJECT 65
- Fill your holes! 65
- SELECTING TARGETS 66
- ADVANCED MODE OPTION 69
- Advanced Use 71
- ADVANCED MODE’S MAIN MENU 72
- STARTING IN ADVANCED MODE 73
- Are you ready? 73
- ADVANCED MODE’S DISPLAYS 74
- ADVANCED MODE’S LEARN DISPLAY 75
- LEARNING TARGETS 76
- Silence please! 76
- LEARN’S TARGET SELECTION 77
- ADVANCED MODE’S EDIT DISPLAY 79
- EDITING PATTERNS 80
- Continued next page 81
- EDITING AND SAVING TARGETS 82
- ADVANCED MODE’S SELECT MENU 83
- SAVING TARGETS 84
- Saving Shortcut 84
- Volume Shortcut 85
- OPTIONS MENU 86
- OPTIONS: NOISE 87
- Noise Shortcut 87
- OPTIONS: RESPONSE 88
- OPTIONS : RESPONSE 89
- OPTIONS: RECOVERY 90
- SETTINGS MENU 91
- Get into the habit 92
- User Info 93
- HELPFUL HINTS 94
- Leading Alkaline 96
- USER PREFERENCES 97
- QUICKSTART MENU STRUCTURE 100
- ADVANCED MENU STRUCTURE 101
- TROUBLESHOOTING 102
- SERVICE REPAIR FORM 103
- WARRANTY 105
- EXPLOPLORER II 106
- EXPLORER II MODEL 107
- GLOSSARY OF TERMS 108
- DETECTOR CARE AND SAFETY 112
Related products and manuals for Measuring, testing & control Minelab EXPLORER II
(25 pages)
(94 pages)
(11 pages)© 2020, manymanuals.com. All rights reserved. | 0.113 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals